- Machined from super strength 4340 steel alloy (far thicker and stronger than the factory part) and black nitride coated for incredible strength and corrosion resistance.
- Closely held CNC machine tolerances eliminate extraneous movement and ensure consistent fit and function
- Compression coil spring improves extractor claw compliance during feeding, lowers cycling effort, and greatly increases service life (virtually unlimited lifetime)
- Robust dimensions and superb geometry ensure no case gets left behind
- Rigorous testing by SASS Cowboy Action Shooters, Marlin Enthusiasts / Machinists; Single Action Shooting Society (SASS) approved
- Drop-in part that installs in minutes (comes with one extractor claw/shaft/spring, one punch, one replacement spring if original is lost)
- Marlin 1894, Marlin 1894CB and Marlin 1894CL options (fits all calibers: .218 Bee, .25-20 Winchester, .32-20 Winchester, .32 H&R Magnum,. 327 Federal, .38 Special, .357 Magnum, .41 Magnum, .44-40 Winchester, .44 Special, .44 Magnum, .45 Colt)
Videos Hide Videos Show Videos
25 Reviews Hide Reviews Show Reviews
The perfect solution to faulty design & manufacturing of the 1894 Marlin. I only had to radius the bottom of the extractor slightly to keep from shaving a tiny bit of brass and causing a "catch" on pickup. Runs jet smooth now and no cartridge is left behind.
#2 is a direct fit for 2017 Marlin 1894 .45 Colt.
Nice Job RPP. Extractor works great.
I installed the RPP M/94 extractor claw into my 1980 Marlin 1894 .357 that had the old style spring steel extractor. Installation was a breeze (after cleaning the crud out of the hole!). Action cycled fine so next step was to get to the range. I also brought my tool kit and my 1995 44 mag rifle so I could install it in that rifle while at the range.
I set up at 50 yards and had 150 rds of PMC .357 and 50 rds of PMC 38spl. I tried the 38spl first, loaded up 5 rounds and chambered the first one without a hitch. This rifle is usually fussy about shooting 38's. Shot the 5 rds without a problem, loaded again, and no problems. Shot the whole box and cycled perfect, neatly tossing the empties at 2 o'clock. I went to the .357 next and had zero issues with those. I shot strings a bit slower as the barrel was getting quite hot but it had zero functioning issues. The action feels like it cycles a bit smoother while feeding and like it did with the 38spl, it put all empties in a nice pile at 2 o'clock. No matter how slow/easy or hard/fast I cycled it, the empties always went at 2 o'clock. Makes it real easy to pick up brass when it's in a neat pile. I shot off bags for most of the session so I was able to keep my brass landing right on the bench by cycling it "softly”.
Once I used up my ammo I took it apart and removed the RPP extractor and sadly re-installed the spring steel stock one. Then I pulled the bolt from the 44 mag, popped out the old extractor and installed the RPP, right there on the shooting bench. Installation was again very quick and easy. After putting the rifle together I got my 44 ammo out and got to work.
The ammo I used for the Marlin 44 mag testing were all reloads from February 1999, 100 of them. I had a pile of 44 mag ammo from 1999 but I'm finally down to my last 4 boxes so I grabbed two for this test run. I loaded up 5 rds, first one fed easily, shot and extracted easily as did the remaining rounds. I noticed during the first 5 shots that I was getting the same ejection of the empties as I had with the .357, all tossed at 2 o'clock. Neither one of these rifles used to do that. I shot the first box of 50 without a hitch, let it cool for a bit while some fellow shooters showed up and got set up. Once shooting resumed, I put the remaining 50 through it without issue. It felt like it cycles smoother than it used to, and did I mention it tosses the empties neatly at 2 c'clock?
I can't wait to get some of these for all my 94's once they get them rolling out. I plan to equip all 5 of my 1894's with this new “claw!’ Big Thank You to Adam/RPP! I'm sold.
Great after market update! Easy installation, make sure to clean the hole well after sliding the old spring type out, then keep as much of the plastic sleeve on this as you can while sliding it in-it helps keep the coil spring from humping out of the slot! Works great at grabbing the case rim without marring it, and the rifle cycles very smoothly when feeding and extracting. Will probably get one for my 1895 in 45/70 as soon as I pay off a new set of truck tires! GREAT customer service!!!
A couple of months back I took the plunge to update my Marlin 1894CS in 357 mag. First I installed the Ranger Point Extractor and immediatly felt a difference when I cycled it. Then I cleaned out the mag tube, shortened the mag spring, and installed a new stainless steel follower. Today I shot my first match with it. What a JOY I had shooting it. It never ran so smooth, and the extractor worked like a charm! I would highly recommend to anyone who has a Marlin 1894 to replace that bobby pin extractor with this Ranger Point Extractor. IMO you cannot go wrong.
Got this installed in my wifes Cowboy Action Marlin '94 and it works great! Easy install and great extraction performance. Exactly as advertised.
Anyone who owns a Marlin model 1894 and has extractor problems should consider purchasing the Ranger Point M/94 extractor claw. Installation is easy and the "Claw" will not disappoint. After installing the M/94 in my Marlin, I have had zero jamming problems. I strongly recommend this finely engineered product.
From my brief experience with my new "Claw" extractor I don't think that I'll ever have to replace it. I, like many other folks, had been having multiple jams with my newly acquired 1894 Marlin and tried everything that I could think of with little result. Then, a friend called me and directed me to your website. I immediately ordered your extractor, installed it and took it to the range yesterday. I fired almost 200 rounds of a variety of ammo, Blazer aluminum SPL, Remington MAG, and Winchester MAG without a single hiccup! I can't tell you how pleased and satisfied I am with the product. I will recommend you to my friends and fellow Range partners whenever the cause arises. Thanks, again. You should be very proud of your work!
The action on rifle is a lot smoother now with the extractor and my single piece firing pin. Another nice thing is my spent brass casings are not all over the place any more. I'm very impressed with the quality of this extractor vs the original.